raspberry 3b+ и cisco wlc/ap, потеря wifi

Всё про WTware на компьютере Raspberry Pi 2 Model B, и Pi 3 Model B и Pi 3B+
http://winterminal.com/ru/
Ответить
sysardex
Сообщения: 20
Зарегистрирован: Вт сен 25, 2018 7:04 am

raspberry 3b+ и cisco wlc/ap, потеря wifi

Сообщение sysardex »

Добрый день. Пытаемся перейти в активную фазу тестирования wtware с дальнейшей покупкой но столкнулись со страной проблемой. wtware на raspberry pi 3b+ при условии что точкой доступа является cisco ap с контроллером и сеть работает только в режиме 5ггц, теряет wifi соединие безвозвратно примерно через минуту работы.
Тестировали на 10 устройствах но везде результат одинаковый. На 2.4 такого не происходит но и работать на этой частоте не реально. Но правда стоит отметить что на raspbian чтобы заработала сеть 5ггц приходиться ставить в настройках вифи country code DE или GB. На стороне циско country code поменять нет возможности, там жестко RU.
В логах до самого последнего момента никаких ошибок не появляется.

Возможно карта в малине меняет country code на ru через минуту после старта.

Прошу помощи.
aka
Разработчик
Разработчик
Сообщения: 10548
Зарегистрирован: Ср окт 01, 2003 12:06 am
Откуда: Роcсия, Тольятти
Контактная информация:

Re: raspberry 3b+ и cisco wlc/ap, потеря wifi

Сообщение aka »

В начале загрузки нажмите Del. "Запустить драйвер Wifi", "подключиться". Когда оно подключится и попросит перегрузить терминал, нажмите Esc. Будет командная строка. Можно дождаться обрыва (пинги пускать с ключом "ping -c 1" чтоб не залипало), и когда оборвётся - снять (или хотя бы посмотреть) лог последним методом "когда на терминале нет сети": https://wtware.ru/logs.html Там же можно попробовать перезапустить wpa_supplicant чтобы копать дальше.
По существу ничего сказать не могу, половины слов не поинимаю :(
sysardex
Сообщения: 20
Зарегистрирован: Вт сен 25, 2018 7:04 am

Re: raspberry 3b+ и cisco wlc/ap, потеря wifi

Сообщение sysardex »

В общем скорее всего все так как я и писал. Попробовал интуитивно добавить в wpa_supplicant.conf строки
country=de (на raspbian 5ггц работает если поставить германию)
update_config=1

Теперь терминал не теряет wifi насовсем но "замирает" каждые 30-40 секунд.

Вот кусок далее бесконечного лога где он скачет с RU на DE и назад:

Код: Выделить всё

[           WPA] [  212.951233] eth0: CTRL-EVENT-DISCONNECTED bssid=70:db:99:66:f5:61 reason=3 locally_generated=1
[           WPA] [  212.951522] nl80211: Failed to open /proc/sys/net/ipv6/conf/eth0/drop_unicast_in_l2_multicast: No such file or directory
[           WPA] [  212.951566] nl80211: Failed to set IPv6 unicast in multicast filter
[           WPA] [  212.976942] eth0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
[           WPA] [  212.979897] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[           WPA] [  215.611357] eth0: Trying to associate with SSID 'fornet5'
[           WPA] [  218.297625] eth0: Associated with 70:db:99:66:f5:61
[           WPA] [  218.297805] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:99:66:f5:61 completed [id=0 id_str=]
[           WPA] [  218.298390] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [  218.298981] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
[           WPA] [  279.511251] eth0: CTRL-EVENT-DISCONNECTED bssid=70:db:99:66:f5:61 reason=3 locally_generated=1
[           WPA] [  279.511465] nl80211: Failed to open /proc/sys/net/ipv6/conf/eth0/drop_unicast_in_l2_multicast: No such file or directory
[           WPA] [  279.511508] nl80211: Failed to set IPv6 unicast in multicast filter
[           WPA] [  279.512226] eth0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
[           WPA] [  279.539559] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[           WPA] [  279.657516] eth0: Trying to associate with SSID 'fornet5'
[           WPA] [  282.298345] eth0: Associated with 70:db:99:66:f5:61
[           WPA] [  282.298509] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:99:66:f5:61 completed [id=0 id_str=]
[           WPA] [  282.299079] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [  282.299626] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
[           WPA] [  346.071337] eth0: CTRL-EVENT-DISCONNECTED bssid=70:db:99:66:f5:61 reason=3 locally_generated=1
[           WPA] [  346.071481] nl80211: Failed to open /proc/sys/net/ipv6/conf/eth0/drop_unicast_in_l2_multicast: No such file or directory
[           WPA] [  346.071523] nl80211: Failed to set IPv6 unicast in multicast filter
[           WPA] [  346.097431] eth0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
[           WPA] [  346.100420] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[           WPA] [  353.801695] eth0: Trying to associate with SSID 'fornet5'
[           WPA] [  356.542661] eth0: Associated with 70:db:99:66:f5:61
[           WPA] [  356.542820] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:99:66:f5:61 completed [id=0 id_str=]
[           WPA] [  356.543401] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [  356.543976] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
[           WPA] [  417.751241] eth0: CTRL-EVENT-DISCONNECTED bssid=70:db:99:66:f5:61 reason=3 locally_generated=1
[           WPA] [  417.751400] nl80211: Failed to open /proc/sys/net/ipv6/conf/eth0/drop_unicast_in_l2_multicast: No such file or directory
[           WPA] [  417.751441] nl80211: Failed to set IPv6 unicast in multicast filter
[           WPA] [  417.777057] eth0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
[           WPA] [  417.780064] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[           WPA] [  420.410457] eth0: Trying to associate with SSID 'fornet5'
[           WPA] [  423.100501] eth0: Associated with 70:db:99:66:f5:61
[           WPA] [  423.100665] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:99:66:f5:61 completed [id=0 id_str=]
[           WPA] [  423.101256] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [  423.102036] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
[           WPA] [  484.311214] eth0: CTRL-EVENT-DISCONNECTED bssid=70:db:99:66:f5:61 reason=3 locally_generated=1
[           WPA] [  484.311375] nl80211: Failed to open /proc/sys/net/ipv6/conf/eth0/drop_unicast_in_l2_multicast: No such file or directory
[           WPA] [  484.311418] nl80211: Failed to set IPv6 unicast in multicast filter
[           WPA] [  484.336909] eth0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
[           WPA] [  484.339865] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[           WPA] [  484.457033] eth0: Trying to associate with SSID 'fornet5'
[           WPA] [  487.101504] eth0: Associated with 70:db:99:66:f5:61
[           WPA] [  487.101853] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:99:66:f5:61 completed [id=0 id_str=]
[           WPA] [  487.102636] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [  487.103333] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
aka
Разработчик
Разработчик
Сообщения: 10548
Зарегистрирован: Ср окт 01, 2003 12:06 am
Откуда: Роcсия, Тольятти
Контактная информация:

Re: raspberry 3b+ и cisco wlc/ap, потеря wifi

Сообщение aka »

1. Попробуй свежую втварь. Может там wpa_supplicant починили.
2. В обновленном распбиане с точно тем же wpa_supplicant.conf не скачет?

PS: не понимаю, при чем здесь страна. В начале соединения ставится страна из конфига, после "Associated with" точка указывает принять другую страну. Не вижу никакой связи между сменой страны и "CTRL-EVENT-DISCONNECTED" через минуту.

Погугли "CTRL-EVENT-DISCONNECTED reason=3 locally_generated=1", там разные идеи есть.

И покажи полный лог.
sysardex
Сообщения: 20
Зарегистрирован: Вт сен 25, 2018 7:04 am

Re: raspberry 3b+ и cisco wlc/ap, потеря wifi

Сообщение sysardex »

1. Самая свежая версия
2. Я до этого проверял минут 5-10 и все было норм, теперь подержал по дольше и да к сожалению тоже возвращается на RU и теряет 5ггц. Но не через 30-60 секунд как на втваре а примерно через 10-15 минут. Если вручную переключить wifi country на DE то снова оживает 5ггц и подключается, что за хрень не понятно. распбиан последний, апдейты последние. Проверил также несколько все ведут себя одинаково.

Можно как то заигнорить со стороны втвари требование точки соскочить на RU? Я подозреваю что производители малины или встроенной вифи карточки забыли пролицензироваться в RU и поэтому тупо отрубают частоты от 5ггц если стоит RU.

Погуглю пока по "CTRL-EVENT-DISCONNECTED reason=3 locally_generated=1" но прошу написать если есть еще какие то идеи.

Весь лог:

Код: Выделить всё

WTware 5.8.88/RPi supervisor.
[        KERNEL] [    0.000000] Booting Linux on physical CPU 0x0
[        KERNEL] [    0.000000] Linux version 4.19.86-v7 (aka@c22) (gcc version 8.3.0 (Debian 8.3.0-2)) #5 SMP Mon Dec 9 15:12:37 UTC 2019
[        KERNEL] [    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[        KERNEL] [    0.000000] CPU: div instructions available: patching division code
[        KERNEL] [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[        KERNEL] [    0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Plus Rev 1.3
[        KERNEL] [    0.000000] Memory policy: Data cache writealloc
[        KERNEL] [    0.000000] cma: Reserved 8 MiB at 0x3ac00000
[        KERNEL] [    0.000000] On node 0 totalpages: 242688
[        KERNEL] [    0.000000]   Normal zone: 1896 pages used for memmap
[        KERNEL] [    0.000000]   Normal zone: 0 pages reserved
[        KERNEL] [    0.000000]   Normal zone: 242688 pages, LIFO batch:63
[        KERNEL] [    0.000000] random: get_random_bytes called from 0x807009cc with crng_init=0
[        KERNEL] [    0.000000] percpu: Embedded 15 pages/cpu s29132 r8192 d24116 u61440
[        KERNEL] [    0.000000] pcpu-alloc: s29132 r8192 d24116 u61440 alloc=15*4096
[        KERNEL] [    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[        KERNEL] [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 240792
[        KERNEL] [    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1080 bcm2708_fb.fbdepth=32 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  dwc_otg.lpm_enable=0 quiet wtboot=mmc
[        KERNEL] [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[        KERNEL] [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[        KERNEL] [    0.000000] Memory: 942060K/970752K available (5120K kernel code, 134K rwdata, 600K rodata, 5120K init, 349K bss, 20500K reserved, 8192K cma-reserved)
[        KERNEL] [    0.000000] Virtual kernel memory layout:
[        KERNEL] [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[        KERNEL] [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[        KERNEL] [    0.000000]     vmalloc : 0xbb800000 - 0xff800000   (1088 MB)
[        KERNEL] [    0.000000]     lowmem  : 0x80000000 - 0xbb400000   ( 948 MB)
[        KERNEL] [    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[        KERNEL] [    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (6112 kB)
[        KERNEL] [    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   (5120 kB)
[        KERNEL] [    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   ( 135 kB)
[        KERNEL] [    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   ( 350 kB)
[        KERNEL] [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[        KERNEL] [    0.000000] rcu: Hierarchical RCU implementation.
[        KERNEL] [    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[        KERNEL] [    0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[        KERNEL] [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[        KERNEL] [    0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[        KERNEL] [    0.000016] Switching to timer-based delay loop, resolution 52ns
[        KERNEL] [    0.000195] Console: colour dummy device 80x30
[        KERNEL] [    0.000210] console [tty0] enabled
[        KERNEL] [    0.000247] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[        KERNEL] [    0.000260] pid_max: default: 32768 minimum: 301
[        KERNEL] [    0.000410] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[        KERNEL] [    0.000424] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[        KERNEL] [    0.001033] CPU: Testing write buffer coherency: ok
[        KERNEL] [    0.001404] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[        KERNEL] [    0.001858] Setting up static identity map for 0x100000 - 0x10003c
[        KERNEL] [    0.001963] rcu: Hierarchical SRCU implementation.
[        KERNEL] [    0.002518] smp: Bringing up secondary CPUs ...
[        KERNEL] [    0.003141] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[        KERNEL] [    0.003828] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[        KERNEL] [    0.004461] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[        KERNEL] [    0.004550] smp: Brought up 1 node, 4 CPUs
[        KERNEL] [    0.004559] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[        KERNEL] [    0.004563] CPU: All CPU(s) started in HYP mode.
[        KERNEL] [    0.004567] CPU: Virtualization extensions available.
[        KERNEL] [    0.005194] devtmpfs: initialized
[        KERNEL] [    0.016273] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[        KERNEL] [    0.016614] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[        KERNEL] [    0.016631] futex hash table entries: 1024 (order: 4, 65536 bytes)
[        KERNEL] [    0.017059] pinctrl core: initialized pinctrl subsystem
[        KERNEL] [    0.018059] NET: Registered protocol family 16
[        KERNEL] [    0.020265] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[        KERNEL] [    0.027629] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[        KERNEL] [    0.067625] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[        KERNEL] [    0.070046] usbcore: registered new interface driver usbfs
[        KERNEL] [    0.070247] usbcore: registered new interface driver hub
[        KERNEL] [    0.070341] usbcore: registered new device driver usb
[        KERNEL] [    0.090174] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-12-05 14:43, variant start
[        KERNEL] [    0.100198] raspberrypi-firmware soc:firmware: Firmware hash is 620e8a436f18c378f8b109a73972b44f9822961d
[        KERNEL] [    0.111887] clocksource: Switched to clocksource arch_sys_counter
[        KERNEL] [    0.124837] NET: Registered protocol family 2
[        KERNEL] [    0.125384] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[        KERNEL] [    0.125415] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[        KERNEL] [    0.125521] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[        KERNEL] [    0.125705] TCP: Hash tables configured (established 8192 bind 8192)
[        KERNEL] [    0.125830] UDP hash table entries: 512 (order: 2, 16384 bytes)
[        KERNEL] [    0.125874] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[        KERNEL] [    0.126045] NET: Registered protocol family 1
[        KERNEL] [    2.377383] Initialise system trusted keyrings
[        KERNEL] [    2.377517] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[        KERNEL] [    2.437223] Key type asymmetric registered
[        KERNEL] [    2.437232] Asymmetric key parser 'x509' registered
[        KERNEL] [    2.437319] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[        KERNEL] [    2.437328] io scheduler noop registered
[        KERNEL] [    2.437499] io scheduler cfq registered (default)
[        KERNEL] [    2.440027] bcm2708_fb soc:fb: FB found 1 display(s)
[        KERNEL] [    2.501005] Console: switching to colour frame buffer device 240x67
[        KERNEL] [    2.536550] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 1920x1080
[        KERNEL] [    2.538733] bcm2835-rng 3f104000.rng: hwrng registered
[        KERNEL] [    2.539173] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[        KERNEL] [    2.539935] vc-sm: Videocore shared memory driver
[        KERNEL] [    2.540583] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[        KERNEL] [    2.541666] zram: Added device: zram0
[        KERNEL] [    2.542898] libphy: Fixed MDIO Bus: probed
[        KERNEL] [    2.542985] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[        KERNEL] [    2.570974] dwc_otg 3f980000.usb: base=(ptrval)
[        KERNEL] [    2.771193] Core Release: 2.80a
[        KERNEL] [    2.771203] Setting default values for core params
[        KERNEL] [    2.771225] Finished setting default values for core params
[        KERNEL] [    2.971499] Using Buffer DMA mode
[        KERNEL] [    2.971505] Periodic Transfer Interrupt Enhancement - disabled
[        KERNEL] [    2.971509] Multiprocessor Interrupt Enhancement - disabled
[        KERNEL] [    2.971515] OTG VER PARAM: 0, OTG VER FLAG: 0
[        KERNEL] [    2.971547] Dedicated Tx FIFOs mode
[        KERNEL] [    2.972144] WARN::dwc_otg_hcd_init:1045: FIQ DMA bounce buffers: virt = bad14000 dma = 0xfad14000 len=9024
[        KERNEL] [    2.972172] FIQ FSM acceleration enabled for :
[        KERNEL] [    2.972172] Non-periodic Split Transactions
[        KERNEL] [    2.972172] Periodic Split Transactions
[        KERNEL] [    2.972172] High-Speed Isochronous Endpoints
[        KERNEL] [    2.972172] Interrupt/Control Split Transaction hack enabled
[        KERNEL] [    2.972180] dwc_otg: Microframe scheduler enabled
[        KERNEL] [    2.972230] WARN::hcd_init_fiq:457: FIQ on core 1
[        KERNEL] [    2.972240] WARN::hcd_init_fiq:458: FIQ ASM at 803b18e4 length 36
[        KERNEL] [    2.972251] WARN::hcd_init_fiq:497: MPHI regs_base at bb810000
[        KERNEL] [    2.972271] dwc_otg 3f980000.usb: DWC OTG Controller
[        KERNEL] [    2.972305] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[        KERNEL] [    2.972338] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[        KERNEL] [    2.972386] Init: Port Power? op_state=1
[        KERNEL] [    2.972390] Init: Power Port (0)
[        KERNEL] [    2.972583] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[        KERNEL] [    2.972594] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[        KERNEL] [    2.972601] usb usb1: Product: DWC OTG Controller
[        KERNEL] [    2.972609] usb usb1: Manufacturer: Linux 4.19.86-v7 dwc_otg_hcd
[        KERNEL] [    2.972616] usb usb1: SerialNumber: 3f980000.usb
[        KERNEL] [    2.973232] hub 1-0:1.0: USB hub found
[        KERNEL] [    2.973277] hub 1-0:1.0: 1 port detected
[        KERNEL] [    2.973992] dwc_otg: FIQ enabled
[        KERNEL] [    2.973997] dwc_otg: NAK holdoff enabled
[        KERNEL] [    2.974001] dwc_otg: FIQ split-transaction FSM enabled
[        KERNEL] [    2.974012] Module dwc_common_port init
[        KERNEL] [    2.975833] usbcore: registered new interface driver usbtouchscreen
[        KERNEL] [    2.978788] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[        KERNEL] [    2.979077] bcm2835-cpufreq: min=600000 max=1400000
[        KERNEL] [    2.979788] sdhci: Secure Digital Host Controller Interface driver
[        KERNEL] [    2.979801] sdhci: Copyright(c) Pierre Ossman
[        KERNEL] [    2.980425] mmc-bcm2835 3f300000.mmcnr: could not get clk, deferring probe
[        KERNEL] [    2.981198] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[        KERNEL] [    2.981428] sdhci-pltfm: SDHCI platform and OF driver helper
[        KERNEL] [    2.981503] hidraw: raw HID events driver (C) Jiri Kosina
[        KERNEL] [    2.982255] usbcore: registered new interface driver usbhid
[        KERNEL] [    2.982261] usbhid: USB HID core driver
[        KERNEL] [    2.983233] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[        KERNEL] [    2.984851] [vc_sm_connected_init]: start
[        KERNEL] [    2.995338] [vc_sm_connected_init]: end - returning 0
[        KERNEL] [    2.996140] NET: Registered protocol family 17
[        KERNEL] [    2.996304] Registering SWP/SWPB emulation handler
[        KERNEL] [    2.996758] Loading compiled-in X.509 certificates
[        KERNEL] [    2.999330] mmc-bcm2835 3f300000.mmcnr: mmc_debug:0 mmc_debug2:0
[        KERNEL] [    2.999341] mmc-bcm2835 3f300000.mmcnr: DMA channel allocated
[        KERNEL] [    3.025634] sdhost: log_buf @ (ptrval) (fad13000)
[        KERNEL] [    3.062684] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[        KERNEL] [    3.064219] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[        KERNEL] [    3.065749] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[        KERNEL] [    3.068491] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[        KERNEL] [    3.071976] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[        KERNEL] [    3.072122] of_cfs_init
[        KERNEL] [    3.072273] of_cfs_init: OK
[        KERNEL] [    3.096012] Freeing unused kernel memory: 5120K
[        KERNEL] [    3.150956] mmc0: host does not support reading read-only switch, assuming write-enable
[        KERNEL] [    3.154007] mmc0: new high speed SDHC card at address 59b4
[        KERNEL] [    3.154815] mmcblk0: mmc0:59b4       7.47 GiB
[        KERNEL] [    3.157018]  mmcblk0: p1
[        KERNEL] [    3.179024] Run /init as init process
[        KERNEL] [    3.180076] random: fast init done
[        KERNEL] [    3.187454] mmc1: new high speed SDIO card at address 0001
[        KERNEL] [    3.221996] Indeed it is in host mode hprt0 = 00021501
[        KERNEL] [    3.432043] usb 1-1: new high-speed USB device number 2 using dwc_otg
[        KERNEL] [    3.432180] Indeed it is in host mode hprt0 = 00001101
[       hotplug] [    3.459230] Block device 179:1. No action.
[       hotplug] [    3.477767] Block device 254:0. No action.
[       hotplug] [    3.478952] Block device 179:0. No action.
[          pfac] [    3.502126] Run /sbin/initrd.
[          pfac] [    3.502409] Ok, PID 649.
[        initrd] [    3.507510] WTware 5.8.88/RPi shell.
[        initrd] [    3.507898] Load font 'ter-c32b.psf', console 120x33.
[        initrd] [    3.553666] HDD/MMC/SD boot.
[        initrd] [    3.553806] No device '/dev/fb1'.
[        KERNEL] [    3.672166] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[        KERNEL] [    3.672177] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[        KERNEL] [    3.672846] hub 1-1:1.0: USB hub found
[        KERNEL] [    3.672968] hub 1-1:1.0: 4 ports detected
[        KERNEL] [    3.991923] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[        KERNEL] [    4.122140] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[        KERNEL] [    4.122152] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[        KERNEL] [    4.122789] hub 1-1.1:1.0: USB hub found
[        KERNEL] [    4.122895] hub 1-1.1:1.0: 3 ports detected
[        KERNEL] [    4.221917] usb 1-1.3: new full-speed USB device number 4 using dwc_otg
[        KERNEL] [    4.358603] usb 1-1.3: New USB device found, idVendor=8086, idProduct=0808, bcdDevice= 1.00
[        KERNEL] [    4.358614] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[        KERNEL] [    4.358623] usb 1-1.3: Product: USB PnP Sound Device
[        KERNEL] [    4.358631] usb 1-1.3: Manufacturer: C-Media Electronics Inc.      
[        KERNEL] [    4.364590] input: C-Media Electronics Inc.       USB PnP Sound Device as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.3/1-1.3:1.2/0003:8086:0808.0001/input/input0
[        KERNEL] [    4.442363] hid-generic 0003:8086:0808.0001: input,hidraw0: USB HID v1.00 Device [C-Media Electronics Inc.       USB PnP Sound Device] on usb-3f980000.usb-1.3/input2
[        KERNEL] [    4.451990] usb 1-1.1.2: new full-speed USB device number 5 using dwc_otg
[        KERNEL] [    4.618980] usb 1-1.1.2: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=24.01
[        KERNEL] [    4.618991] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[        KERNEL] [    4.618999] usb 1-1.1.2: Product: USB Receiver
[        KERNEL] [    4.619008] usb 1-1.1.2: Manufacturer: Logitech
[        KERNEL] [    4.646708] logitech-djreceiver 0003:046D:C52B.0004: hiddev96,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-3f980000.usb-1.1.2/input2
[        KERNEL] [    4.796928] input: Logitech M215 2nd Gen as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.2/0003:046D:C52B.0004/0003:046D:401B.0005/input/input1
[        KERNEL] [    4.797321] logitech-hidpp-device 0003:046D:401B.0005: input,hidraw2: USB HID v1.11 Mouse [Logitech M215 2nd Gen] on usb-3f980000.usb-1.1.2:1
[        KERNEL] [    4.810979] input: Logitech K330 as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.2/0003:046D:C52B.0004/0003:046D:4016.0006/input/input2
[        KERNEL] [    4.811716] logitech-hidpp-device 0003:046D:4016.0006: input,hidraw3: USB HID v1.11 Keyboard [Logitech K330] on usb-3f980000.usb-1.1.2:2
[        initrd] [    5.052815] Success: /dev/mmcblk0p1 mounted to /bootmedia.
/--- FILE "/bootmedia/config.txt" -----------------------
| # For more options and information see:
| #
| # https://www.raspberrypi.org/documentation/configuration/config-txt/README.md
| #
| # Some settings may impact device functionality. See link above for details.
| # Uncomment if you get no picture on HDMI for a default "safe" mode.
| #hdmi_safe=1
| # Uncomment this if your display has a black border of unused pixels visible
| # and your display can output without overscan.
| disable_overscan=1
| # Uncomment if hdmi display is not detected and composite is being output.
| #hdmi_force_hotplug=1
| # Uncomment to force a specific HDMI mode (this will force VGA).
| #hdmi_group=1
| #hdmi_mode=1
| # Force the monitor to HDMI mode so that sound will be sent over HDMI cable.
| #hdmi_drive=2
| # Uncomment to increase signal to HDMI, if you have interference, blanking, or
| # no display.
| #config_hdmi_boost=4
| # Uncomment to overclock the arm. 700 MHz is the default.
| #arm_freq=800
| disable_splash=1
| framebuffer_depth=32
| # Uncomment for 16-bit color.
| #framebuffer_depth=16
| # Enable onboard audio (HDMI or jack).
| dtparam=audio=on
| # Removes the warning overlay.
| #avoid_warnings=1
| # Additionally allows turbo when low-voltage is present.
| #avoid_warnings=2
| [pi4]
| max_framebuffers=2
| [all]
| # Uncomment these two lines to set display resolution:
| #hdmi_group=2
| #hdmi_mode=58
| #
| # Specify correct value in hdmi_mode= line from the list of valid values:
| # 800x600:   hdmi_mode=9
| # 1024x768:  hdmi_mode=16
| # 1280x1024: hdmi_mode=35
| # 1360x768:  hdmi_mode=39
| # 1400x1050: hdmi_mode=42
| # 1440x900:  hdmi_mode=47
| # 1600x1200: hdmi_mode=51
| # 1680x1050: hdmi_mode=58
| # 1366x768:  hdmi_mode=81
| # 1920x1080: hdmi_mode=82
| # 1920x1200: hdmi_mode=69
| #
| # Find more resolutions in manual:
| # https://www.raspberrypi.org/documentation/configuration/config-txt/video.md
| #
| # Uncomment six lines with such syntax and right hdmi_mode= values for
| # dual displays on Raspberry Pi 4:
| #
| #[HDMI:0]
| # hdmi_group=2
| # hdmi_mode=42
| #[HDMI:1]
| # hdmi_group=2
| # hdmi_mode=58
| hdmi_group=2
| hdmi_mode=82
\----------------------------------------------------
[        KERNEL] [    5.101933] usb 1-1.1.1: new high-speed USB device number 6 using dwc_otg
[        initrd] [    5.118170] Do not cache package files.
[        initrd] [    5.118306] WTpassword present: 8f28f72571b1fge300809a00aec3d8b2.
[        initrd] [    5.188335] USB: 046d:c52b Logitech, Inc. Unifying Receiver.
[        initrd] [    5.188421] USB: 8086:0808 Intel Corp..
[        initrd] [    5.188454] USB: 0424:2514 Standard Microsystems Corp. USB 2.0 Hub.
[        KERNEL] [    5.232301] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800, bcdDevice= 3.00
[        KERNEL] [    5.232312] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[        KERNEL] [    5.531922] usb 1-1.1.3: new full-speed USB device number 7 using dwc_otg
[        KERNEL] [    5.678476] usb 1-1.1.3: New USB device found, idVendor=0b0e, idProduct=0303, bcdDevice= 3.00
[        KERNEL] [    5.678487] usb 1-1.1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[        KERNEL] [    5.678495] usb 1-1.1.3: Product: Jabra EVOLVE 20
[        KERNEL] [    5.678504] usb 1-1.1.3: Manufacturer: GN Netcom A/S
[        KERNEL] [    5.678511] usb 1-1.1.3: SerialNumber: 0000A9396CC607
[        KERNEL] [    5.694071] input: GN Netcom A/S Jabra EVOLVE 20 as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1/1-1.1.3/1-1.1.3:1.3/0003:0B0E:0303.0007/input/input3
[        KERNEL] [    5.762472] input: GN Netcom A/S Jabra EVOLVE 20 as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1/1-1.1.3/1-1.1.3:1.3/0003:0B0E:0303.0007/input/input4
[        KERNEL] [    5.762987] input: GN Netcom A/S Jabra EVOLVE 20 Consumer Control as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1/1-1.1.3/1-1.1.3:1.3/0003:0B0E:0303.0007/input/input5
[        KERNEL] [    5.763517] hid-generic 0003:0B0E:0303.0007: input,hiddev97,hidraw4: USB HID v1.00 Device [GN Netcom A/S Jabra EVOLVE 20] on usb-3f980000.usb-1.1.3/input3
/--- FILE "/bootmedia/configs/initrd.wtc" -----------------------
| [BOM]
| clientIP=*
| config=local
| netmedia=wifi
| setupPassword=8f28f72571b1fge300809a00aec3d8b2
| wifi_ssid=fornet5
| wifi_channel=40
| wifi_security=wpa_psk
Skip 'wifi_key='.
\----------------------------------------------------
[        initrd] [    7.006041] Load Wi-Fi wireless network card driver.
[        initrd] [    7.006161] Unpack /bootmedia/packages/pi2-dbus.
[        initrd] [    7.236910] +--- Executing "/usr/bin/dbus-uuidgen --ensure"
[        KERNEL] [    7.238546] random: crng init done
[        initrd] [    7.241798] +- Errorlevel: 0, output:
File is empty.
[        initrd] [    7.241944] +------------------------
[        initrd] [    7.241979] +--- Executing "/usr/bin/dbus-daemon --system "
[        initrd] [    7.282972] +- Errorlevel: 0, output:
File is empty.
[        initrd] [    7.283193] +------------------------
[        initrd] [    7.283229] Run '/usr/bin/dbus-daemon --session --address=unix:path=/run/user/1007/bus', log '', env '', pid ''.
[          pfac] [    7.283490] Run /usr/bin/dbus-daemon --session --address=unix:path=/run/user/1007/bus.
[        initrd] [    7.283532] Unpack /bootmedia/packages/pi2-xnet.
[          pfac] [    7.283579] Ok, PID 732.
[        initrd] [    8.381228] Find SDIO device 'sdio:c02v02D0dA9A6'.
[        initrd] [    8.381323] Load driver for Pi 3 onboard Wi-Fi.
[        initrd] [    8.381362] modprobe brcmfmac.
[        KERNEL] [    8.392145] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[        KERNEL] [    8.397310] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[        KERNEL] [    8.411061] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[        KERNEL] [    8.545106] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[        KERNEL] [    8.553576] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[        KERNEL] [    8.608543] brcmfmac mmc1:0001:1 eth0: renamed from wlan0
[        initrd] [    8.655165] Copy /bootmedia/configs/wpa_supplicant.conf to /etc/wpa.conf.
[        KERNEL] [    8.652190] brcmfmac: power management disabled
[        initrd] [    8.656304] /bootmedia/configs/wpa_supplicant.conf -> /etc/wpa.conf, 125 bytes copied.
/--- FILE "/etc/wpa.conf" -----------------------
| country=de
| update_config=1
| ctrl_interface=/var/run/wpa_supplicant
| network={
|      ssid="fornet5"
Skip 'psk='.
| }
\----------------------------------------------------
[        initrd] [    8.656706] +--- Executing "/sbin/wpa_supplicant -B -c /etc/wpa.conf -i eth0 -f /tmp/wpa_supplicant.out"
[           WPA] [    8.678092] Successfully initialized wpa_supplicant
[           WPA] [    8.711054] rfkill: Cannot open RFKILL control device
[        KERNEL] [    8.738105] brcmfmac: power management disabled
[           WPA] [    8.977578] rfkill: Cannot get wiphy information
[           WPA] [    8.982759] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[        initrd] [    8.982965] +- Errorlevel: 0, output:
File is empty.
[        initrd] [    8.983113] +------------------------
[        initrd] [    8.987296] State SCANNING before handshake, do nothing.
[        initrd] [    9.295371] State SCANNING before handshake, do nothing.
[        initrd] [    9.603371] State SCANNING before handshake, do nothing.
[        initrd] [    9.911395] State SCANNING before handshake, do nothing.
[        initrd] [   10.219245] State SCANNING before handshake, do nothing.
[        initrd] [   10.527078] State SCANNING before handshake, do nothing.
[        initrd] [   10.834998] State SCANNING before handshake, do nothing.
[        initrd] [   11.142897] State SCANNING before handshake, do nothing.
[        initrd] [   11.450858] State SCANNING before handshake, do nothing.
[           WPA] [   11.542632] eth0: Trying to associate with SSID 'fornet5'
[        initrd] [   11.758913] State ASSOCIATING before handshake, do nothing.
[        initrd] [   12.066823] State ASSOCIATING before handshake, do nothing.
[        initrd] [   12.374776] State ASSOCIATING before handshake, do nothing.
[        initrd] [   12.682747] State ASSOCIATING before handshake, do nothing.
[        initrd] [   12.991160] State ASSOCIATING before handshake, do nothing.
[        initrd] [   13.299050] State ASSOCIATING before handshake, do nothing.
[        initrd] [   13.606866] State ASSOCIATING before handshake, do nothing.
[        initrd] [   13.914841] State ASSOCIATING before handshake, do nothing.
[        initrd] [   14.222917] State ASSOCIATING before handshake, do nothing.
[           WPA] [   14.242052] eth0: Associated with 70:db:48:68:f0:3d
[           WPA] [   14.242201] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:48:68:f0:3d completed [id=0 id_str=]
[           WPA] [   14.242873] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [   14.243481] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
[        initrd] [   14.531107] wpa_state=COMPLETED
[        initrd] [   14.531223] WTpassword present: 8f28f72571b1fge300809a00aec3d8b2.
[        initrd] [   15.800188] dhcp: 332 bytes from 1.1.1.1.
[        initrd] [   15.800321] 00000000:00000138000000000011000001010101C0A8FA81004300440138000002010601  ...8................C.D.8......
[        initrd] [   15.800402] 00000020:67458B6B0000000000000000C0A8FA810000000000000000B827EB2B8DFE0000  gE.k.....................'.+....
[        initrd] [   15.800478] 00000040:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   15.800553] 00000060:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   15.800628] 00000080:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   15.800701] 000000a0:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   15.800776] 000000c0:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   15.800849] 000000e0:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   15.800923] 00000100:0000000000000000638253633501023604010101013304000017700104FFFFFF  ........c.Sc5..6.....3...p.....
[        initrd] [   15.800996] 00000120:000304C0A8FA010604C0A8D20A0F0B6578616D706C652E6F7267000000000000  ...............example.org......
[        initrd] [   15.801070] 00000140:00000000000000FF00000000                                          ............
[        initrd] [   16.960224] dhcp: 332 bytes from 1.1.1.1.
[        initrd] [   16.960329] 00000000:00000138000000000011000001010101C0A8FA81004300440138000002010601  ...8................C.D.8......
[        initrd] [   16.960407] 00000020:67458B6B0000000000000000C0A8FA810000000000000000B827EB2B8DFE0000  gE.k.....................'.+....
[        initrd] [   16.960482] 00000040:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   16.960575] 00000060:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   16.960649] 00000080:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   16.960723] 000000a0:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   16.960796] 000000c0:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   16.960870] 000000e0:0000000000000000000000000000000000000000000000000000000000000000  ................................
[        initrd] [   16.960943] 00000100:0000000000000000638253633501053604010101013304000017700104FFFFFF  ........c.Sc5..6.....3...p.....
[        initrd] [   16.961016] 00000120:000304C0A8FA010604C0A8D20A0F0B6578616D706C652E6F7267000000000000  ...............example.org......
[        initrd] [   16.961090] 00000140:00000000000000FF00000000                                          ............
[        initrd] [   17.020093] [DHCP] DHCP server address 1.1.1.1.
[        initrd] [   17.020176] [DHCP] IP 192.168.250.129 mask 255.255.255.0.
[        initrd] [   17.020250] [DHCP] Default gateway 192.168.250.1.
[        initrd] [   17.020323] [DHCP] DNS 192.168.175.10.
[        initrd] [   17.020397]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
[        initrd] [   17.020471]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
[        initrd] [   17.020545] [DHCP] Domain example.org.
[        initrd] [   17.020617]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
[        initrd] [   17.020691] [DHCP] TFTP = DHCP 1.1.1.1.
[        initrd] [   17.020762] [DHCP] TFTP 1.1.1.1.
[        initrd] [   17.020834]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
[        initrd] [   17.020908] [DHCP] No boot file from DHCP.
[        initrd] [   17.020980] [DHCP] TFTP binary "", configs prefix "", using "/" slash.
[        initrd] [   17.021053]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
[        initrd] [   17.021126]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
[        initrd] [   17.021199]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
[        initrd] [   17.021274]                  dhcp_common.h (  237): -- ERROR -- INTERNAL ERROR. Please, contact WTware tech support.
WTC listener is active.
WTC broadcast listener is active.
Send broadcast WTCU discover.
[          pfac] [   17.024915] Run /sbin/httpd.
[        initrd] [   17.024999] Run '/sbin/httpd', log '/tmp/httpd.out', env '', pid ''.
[          pfac] [   17.025113] Ok, PID 782.
[        initrd] [   17.025162] Copy /bootmedia/configs/config.wtc to /tmp/config.wtc.
[        initrd] [   17.025242] /bootmedia/configs/config.wtc -> /tmp/config.wtc, 674 bytes copied.
[        initrd] [   17.025322] Common local disk config:
/--- FILE "/tmp/config.wtc" -----------------------
| [BOM]
| server=192.168.175.15
| display=1920x1080, HDMI
| SIP=401:123@192.168.175.62, ring:0:0, talk:2:0, nolock
| SIP_usb_sound_level=70, infobox
| sound=on, amixer:cset numid=3 2
| clienthostname=wt*IP1
| disk=usb
| domain=DOMAIN
| graphic=abcf
| language=ru,default
| sound_rate=48000
| microphone_level=95
| sound_buffer=250
| connection 
\----------------------------------------------------
/--- FILE "/etc/config.compiled" -----------------------
| [BOM]
| server=192.168.175.15
| display=1920x1080, HDMI
| SIP=401:123@192.168.175.62, ring:0:0, talk:2:0, nolock
| SIP_usb_sound_level=70, infobox
| sound=on, amixer:cset numid=3 2
| clienthostname=wt*IP1
| disk=usb
| domain=DOMAIN
| graphic=abcf
| language=ru,default
| sound_rate=48000
| microphone_level=95
| sound_buffer=250
| connection 
\----------------------------------------------------
[        initrd] [   17.028636] Hostname: "wt-129".
[         httpd] [   17.036701] Internal HTTP Server, WTware 5.8.88/RPi
[        initrd] [   17.290419] [NTP] 42 DHCP option is not set.
Everyone can control terminal by RSH.
RSH: listener is active.
Send broadcast WTCU discover.
[         httpd] [   17.295257] Reread settings.
[        initrd] [   17.295423] Unpack /bootmedia/packages/pi2-f.
[         httpd] [   17.295473] Everyone can control terminal by HTTP.
[            gm] [   17.468433] WTware 5.8.88/RPi session manager.
[            gm] [   17.469368] Add keyboard event5: GN Netcom A/S Jabra EVOLVE 20 Consumer Control.
[            gm] [   17.469410] EV_ABS flag found. Add mouse event4: GN Netcom A/S Jabra EVOLVE 20.
[            gm] [   17.469446] Add keyboard event3: GN Netcom A/S Jabra EVOLVE 20.
[            gm] [   17.469480] Add keyboard event2: Logitech K330.
[            gm] [   17.469514] EV_REL flag found. Add mouse event1: Logitech M215 2nd Gen.
[            gm] [   17.469548] Add keyboard event0: C-Media Electronics Inc.       USB PnP Sound Device.
[            gm] [   17.469586] Display mode: 1920x1080, 32 bit, landscape, 0 Hz, modeline "", DDC enabled, connector 0.
[            gm] [   17.941939] Framebuffer device found.
[            gm] [   17.942025] LINELENBYTES 7680
[            gm] [   17.942065] VLEN 8294400
[            gm] [   17.943687] Use /lib/ui32.so.
[            gm] [   17.969755] Unpack /bootmedia/packages/pi2-alsa.
[            gm] [   18.151201] modprobe snd-bcm2835.
[        KERNEL] [   18.161725] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[            gm] [   18.163968] modprobe snd-usb-audio.
[        KERNEL] [   18.164919] bcm2835_audio soc:audio: card created with 8 channels
[        KERNEL] [   18.194478] usb 1-1.1.3: 1:1: cannot get freq at ep 0x83
[        KERNEL] [   18.198359] usb 1-1.1.3: 2:1: cannot get freq at ep 0x4
/--- FILE "/proc/asound/devices" -----------------------
|   0: [ 0]   : control
|  16: [ 0- 0]: digital audio playback
|  17: [ 0- 1]: digital audio playback
|  18: [ 0- 2]: digital audio playback
|  32: [ 1]   : control
|  33:        : timer
|  56: [ 1- 0]: digital audio capture
|  64: [ 2]   : control
|  80: [ 2- 0]: digital audio playback
|  88: [ 2- 0]: digital audio capture
\----------------------------------------------------
[        KERNEL] [   18.244752] usbcore: registered new interface driver snd-usb-audio
[            gm] [   18.245575] /dev/snd//controlC2 character device.
[            gm] [   18.245736] /dev/snd//pcmC2D0c character device.
[            gm] [   18.245862] /dev/snd//pcmC2D0p character device.
[            gm] [   18.245960] /dev/snd//controlC1 character device.
[            gm] [   18.246080] /dev/snd//pcmC1D0c character device.
[            gm] [   18.246192] /dev/snd//controlC0 character device.
[            gm] [   18.246298] /dev/snd//pcmC0D2p character device.
[            gm] [   18.246379] /dev/snd//pcmC0D1p character device.
[            gm] [   18.246460] /dev/snd//pcmC0D0p character device.
[            gm] [   18.246546] /dev/snd//timer character device.
[            gm] [   18.246666] +--- Executing "/usr/bin/amixer cset numid=3 2"
[            gm] [   18.261969] +- Errorlevel: 0, output:
| numid=3,iface=MIXER,name='PCM Playback Route'
|   ; type=INTEGER,access=rw------,values=1,min=0,max=3,step=0
|   : values=2
[            gm] [   18.262219] +------------------------
[            gm] [   18.262255] Run '/sbin/rdpsnd sndvol 100 95 70', log '', env '', pid ''.
[          pfac] [   18.262668] Run /sbin/rdpsnd sndvol 100 95 70.
[            gm] [   18.262710] Run sound daemon.
[          pfac] [   18.262757] Ok, PID 817.
[            gm] [   18.262779] Run '/sbin/rdpsnd 1 48000 250 0 -1', log '', env '', pid ''.
[          pfac] [   18.262819] Run /sbin/rdpsnd 1 48000 250 0 -1.
[            gm] [   18.262847] [SIP] Contacts list contacts.txt not found.
[          pfac] [   18.262887] Ok, PID 818.
/--- FILE "/.linphonerc" -----------------------
| [audio_codec_0]
| mime=opus
| rate=48000
| channels=1
| enabled=1
| [audio_codec_1]
| mime=SILK
| rate=16000
| channels=1
| enabled=1
| [audio_codec_2]
| mime=BV16
| rate=8000
| channels=1
| enabled=1
| [audio_codec_3]
| mime=speex
| rate=16000
| channels=1
| enabled=1
| [audio_codec_4]
| mime=speex
| rate=8000
| channels=1
| enabled=1
| [audio_codec_5]
| mime=G729
| rate=8000
| enabled=1
| [audio_codec_6]
| mime=GSM
| rate=8000
| channels=1
| enabled=1
| [audio_codec_7]
| mime=G722
| rate=8000
| channels=1
| enabled=1
| [audio_codec_8]
| mime=PCMU
| rate=8000
| channels=1
| enabled=1
| [audio_codec_9]
| mime=PCMA
| rate=8000
| channels=1
| enabled=1
| [net]
| adaptive_rate_control=1
| mtu=0
| [sip]
| ipv6_migration_done=1
| use_ipv6=0
| [sound]
| echocancellation=1
| remote_ring=/usr/local/share/sounds/linphone/rings/ringback.wav
| local_ring=/usr/local/share/sounds/linphone/rings/oldphone.wav
| ringer_dev_id=ALSA: bcm2835 ALSA
| playback_dev_id=ALSA: Jabra EVOLVE 20
| capture_dev_id=ALSA: Jabra EVOLVE 20
\----------------------------------------------------
[            gm] [   18.263433] /.linphonerc -> /.linphonerc.orig, 910 bytes copied.
[            gm] [   18.263532] Unpack /bootmedia/packages/pi2-lstdcpp.
[        rdpsnd] [   18.265863] RDP Sound Redirector, WTware 5.8.88/RPi.
[        sndvol] [   18.266522] [ALSA] Sound cards found: 3.
[        sndvol] [   18.269136] Card 'ALSA'/'bcm2835 ALSA'.
[        sndvol] [   18.269191] Mixer name: 'Broadcom Mixer'.
[        sndvol] [   18.269235] Components: ''.
[        sndvol] [   18.269272] Controls: 5.
[        sndvol] [   18.269308] ALSA: control 'PCM Playback Volume'.
[        sndvol] [   18.269344] ALSA: control 'PCM Playback Switch'.
[        sndvol] [   18.269380] ALSA: control 'PCM Playback Route'.
[        sndvol] [   18.269417] ALSA: control 'IEC958 Playback Default'.
[        sndvol] [   18.269452] ALSA: control 'IEC958 Playback Con Mask'.
[        sndvol] [   18.269488] Card 'Device'/'C-Media Electronics Inc. USB PnP Sound Device at usb-3f980000.usb-1.3, full spe'.
[        sndvol] [   18.269525] Mixer name: 'USB Mixer'.
[        sndvol] [   18.269561] Components: 'USB8086:0808'.
[        sndvol] [   18.269597] Controls: 5.
[        sndvol] [   18.269632] ALSA: control 'Capture Channel Map'.
[        sndvol] [   18.269668] ALSA: control 'Mic Capture Switch'.
[        sndvol] [   18.269745] ALSA: control 'Mic Capture Volume'.
[        sndvol] [   18.270103] ALSA: control 'Auto Gain Control'.
[        sndvol] [   18.270143] ALSA: control 'Keep Interface'.
[        sndvol] [   18.270242] Card 'J20'/'GN Netcom A/S Jabra EVOLVE 20 at usb-3f980000.usb-1.1.3, full speed'.
[        sndvol] [   18.270280] Mixer name: 'USB Mixer'.
[        sndvol] [   18.270316] Components: 'USB0b0e:0303'.
[        sndvol] [   18.270352] Controls: 9.
[        sndvol] [   18.270388] ALSA: control 'Capture Channel Map'.
[        sndvol] [   18.270424] ALSA: control 'Playback Channel Map'.
[        sndvol] [   18.270461] ALSA: control 'Sidetone Playback Switch'.
[        sndvol] [   18.270499] ALSA: control 'Sidetone Playback Volume'.
[        sndvol] [   18.270534] ALSA: control 'Speaker Playback Switch'.
[        sndvol] [   18.270736] ALSA: control 'Speaker Playback Volume'.
[        sndvol] [   18.270774] ALSA: control 'Mic Capture Switch'.
[        sndvol] [   18.272384] ALSA: control 'Mic Capture Volume'.
[        sndvol] [   18.272444] ALSA: control 'Keep Interface'.
[          pfac] [   18.273449] Process pid 817 terminated, status 00000000.
[            gm] [   18.352787] Unpack /bootmedia/packages/pi2-xml2.
[            gm] [   22.208641] Unpack /bootmedia/packages/pi2-linphone.
[            gm] [   23.752253] Run '/usr/local/bin/linphonec -l /tmp/linphone.out --pipe', log '/tmp/linphone.out', env '', pid '/run/linphone.pid'.
[          pfac] [   23.752406] Run /usr/local/bin/linphonec -l /tmp/linphone.out --pipe.
[            gm] [   23.752445] Load ISO 9660 and UDF CDROM filesystem drivers.
[          pfac] [   23.752512] Ok, PID 819.
[            gm] [   23.752552] modprobe udf.
[            gm] [   23.759396] modprobe isofs.
[            gm] [   23.766158] Load usb storage driver.
[            gm] [   23.766288] modprobe scsi_mod.
[            gm] [   23.775172] modprobe usb-storage.
[        KERNEL] [   23.776082] SCSI subsystem initialized
[            gm] [   23.784199] modprobe uas.
[        KERNEL] [   23.785341] usbcore: registered new interface driver usb-storage
[        KERNEL] [   23.791394] usbcore: registered new interface driver uas
[            gm] [   23.790270] modprobe sd_mod.
[            gm] [   23.796791] Load EXFAT filesystem driver.
[            gm] [   23.796902] modprobe fuse.
[            gm] [   23.806269] modprobe exfat.
[        KERNEL] [   23.806991] fuse init (API version 7.27)
[        KERNEL] [   23.815523] exFAT: Version 1.2.9
[            gm] [   23.862231] Run '/sbin/resolver 0x1794300 dns [192.168.175.15]', log '', env '', pid ''.
[            gm] [   23.862330] Nobody can control terminal by VNC.
[            gm] [   23.862375] [SIP] Command: 'register sip:401@192.168.175.62 192.168.175.62 sneRTz1bs16zlqY'.
[          pfac] [   23.862679] Run /sbin/resolver 0x1794300 dns [192.168.175.15].
[          pfac] [   23.862757] Ok, PID 858.
[          pfac] [   23.864740] Process pid 858 terminated, status 00000000.
[        KERNEL] [   23.906084] usb 1-1.1.3: 1:1: cannot get freq at ep 0x83
[           SIP] [   23.987991] Warning: video is disabled in linphonec, use -V or -C or -D to enable.
[           SIP] [   24.862616] linphonec> Receiving command 'register sip:401@192.168.175.62 192.168.175.62 123'
[            gm] [   24.882817] [SIP] State 'sip_state_not_running' => 'sip_state_idle'.
[            gm] [   24.883045] 192.168.175.15 => 192.168.175.15.
[          pfac] [   24.895278] Run /sbin/rdpclient 1.
[            gm] [   24.895392] Free ram before fork terminal client /sbin/rdpclient (session 1): 838388 Kb.
[          pfac] [   24.895524] Ok, PID 861.
[            gm] [   24.895578] Run '/sbin/rdpclient 1', log '/tmp/rdpclient.out', env '', pid ''.
[ rdpclient 861] [   24.903607] RDP Terminal Client, WTware 5.8.88/RPi, pipe 1, pid 861.
[ rdpclient 861] [   24.904035] Use /lib/ui32.so.
[ rdpclient 861] [   24.904640] Redirect sound.
[ rdpclient 861] [   24.904880] Make RDP session with 192.168.175.15, port 3389.
[ rdpclient 861] [   24.904928]  No username.
[ rdpclient 861] [   24.904971]  No password.
[ rdpclient 861] [   24.905014]  No PIN.
[ rdpclient 861] [   24.905051]  Domain: "DOMAIN".
[ rdpclient 861] [   24.905090]  No shell.
[ rdpclient 861] [   24.905156]  No directory.
[ rdpclient 861] [   24.905207]  Window: 1856x1080@24.
[ rdpclient 861] [   24.905250]  PFlags 0x000000A8.
[ rdpclient 861] [   24.905289]  Keyboard 00000409:00000000.
[ rdpclient 861] [   24.905330]  My hostname "wt-129".
[ rdpclient 861] [   24.905370] TCP: connecting to 192.168.175.15:3389.
[ rdpclient 861] [   24.908136] TCP: connection with 192.168.175.15:3389 established.
[ rdpclient 861] [   24.908333] Turn keepalive on.
[ rdpclient 861] [   24.909080] Free ram after buffers allocation: 837340 KB.
[ rdpclient 861] [   24.920313] Process RDP server certificate.
[ rdpclient 861] [   24.920392] RDP5 encryption (X.509).
[ rdpclient 861] [   24.961293] Enable font smoothing.
[ rdpclient 861] [   25.068797] 32-bit color.
[ rdpclient 861] [   57.410389] errorInfo 0x00000000.
[ rdpclient 861] [   57.411020] Receive Disconnect Provider Ultimatum.
[            gm] [   57.411120] TSClient (sessionId 1, pid 861) gracefully end.
[          pfac] [   57.415323] Process pid 861 terminated, status 00000009.
[        rdpsnd] [   57.415408] Link lost.
[            gm] [   57.423122] Run '/sbin/resolver 0x1794300 dns [192.168.175.15]', log '', env '', pid ''.
[          pfac] [   57.423892] Run /sbin/resolver 0x1794300 dns [192.168.175.15].
[          pfac] [   57.424030] Ok, PID 869.
[          pfac] [   57.429543] Process pid 869 terminated, status 00000000.
[            gm] [   57.433360] 192.168.175.15 => 192.168.175.15.
[            gm] [   57.438470] Free ram before fork terminal client /sbin/rdpclient (session 2): 836476 Kb.
[          pfac] [   57.438832] Run /sbin/rdpclient 2.
[            gm] [   57.438868] Run '/sbin/rdpclient 2', log '/tmp/rdpclient.out', env '', pid ''.
[          pfac] [   57.438917] Ok, PID 870.
[ rdpclient 870] [   57.446287] RDP Terminal Client, WTware 5.8.88/RPi, pipe 2, pid 870.
[ rdpclient 870] [   57.446809] Use /lib/ui32.so.
[ rdpclient 870] [   57.447449] Redirect sound.
[ rdpclient 870] [   57.447766] Make RDP session with 192.168.175.15, port 3389.
[ rdpclient 870] [   57.447824]  No username.
[ rdpclient 870] [   57.447871]  No password.
[ rdpclient 870] [   57.447910]  No PIN.
[ rdpclient 870] [   57.447950]  Domain: "DOMAIN".
[ rdpclient 870] [   57.447990]  No shell.
[ rdpclient 870] [   57.448029]  No directory.
[ rdpclient 870] [   57.448067]  Window: 1856x1080@24.
[ rdpclient 870] [   57.448107]  PFlags 0x000000A8.
[ rdpclient 870] [   57.448146]  Keyboard 00000409:00000000.
[ rdpclient 870] [   57.448183]  My hostname "wt-129".
[ rdpclient 870] [   57.448220] TCP: connecting to 192.168.175.15:3389.
[ rdpclient 870] [   57.450345] TCP: connection with 192.168.175.15:3389 established.
[ rdpclient 870] [   57.450525] Turn keepalive on.
[ rdpclient 870] [   57.451251] Free ram after buffers allocation: 836476 KB.
[ rdpclient 870] [   57.460397] Process RDP server certificate.
[ rdpclient 870] [   57.460475] RDP5 encryption (X.509).
[ rdpclient 870] [   57.473404] Enable font smoothing.
[ rdpclient 870] [   57.569029] 32-bit color.
[           WPA] [   74.711344] eth0: CTRL-EVENT-DISCONNECTED bssid=70:db:48:68:f0:3d reason=3 locally_generated=1
[           WPA] [   74.711893] nl80211: Failed to open /proc/sys/net/ipv6/conf/eth0/drop_unicast_in_l2_multicast: No such file or directory
[           WPA] [   74.711940] nl80211: Failed to set IPv6 unicast in multicast filter
[           WPA] [   74.737162] eth0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
[           WPA] [   74.740367] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[           WPA] [   74.857432] eth0: Trying to associate with SSID 'fornet5'
[           WPA] [   77.525976] eth0: Associated with 70:db:48:68:f0:3d
[           WPA] [   77.526139] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:48:68:f0:3d completed [id=0 id_str=]
[           WPA] [   77.526770] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [   77.527345] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
[ rdpclient 870] [   89.883680] errorInfo 0x00000000.
[            gm] [   89.883929] TSClient (sessionId 2, pid 870) gracefully end.
[ rdpclient 870] [   89.883986] Receive Disconnect Provider Ultimatum.
[        rdpsnd] [   89.887990] Link lost.
[          pfac] [   89.888392] Process pid 870 terminated, status 00000009.
[            gm] [   89.891325] Run '/sbin/resolver 0x1794300 dns [192.168.175.15]', log '', env '', pid ''.
[          pfac] [   89.891776] Run /sbin/resolver 0x1794300 dns [192.168.175.15].
[          pfac] [   89.891891] Ok, PID 875.
[          pfac] [   89.895167] Process pid 875 terminated, status 00000000.
[            gm] [   89.899995] 192.168.175.15 => 192.168.175.15.
[            gm] [   89.905191] Free ram before fork terminal client /sbin/rdpclient (session 3): 836252 Kb.
[            gm] [   89.905250] Run '/sbin/rdpclient 3', log '/tmp/rdpclient.out', env '', pid ''.
[          pfac] [   89.905296] Run /sbin/rdpclient 3.
[          pfac] [   89.905521] Ok, PID 876.
[ rdpclient 876] [   89.912944] RDP Terminal Client, WTware 5.8.88/RPi, pipe 3, pid 876.
[ rdpclient 876] [   89.913340] Use /lib/ui32.so.
[ rdpclient 876] [   89.914049] Redirect sound.
[ rdpclient 876] [   89.914247] Make RDP session with 192.168.175.15, port 3389.
[ rdpclient 876] [   89.914292]  No username.
[ rdpclient 876] [   89.914339]  No password.
[ rdpclient 876] [   89.914380]  No PIN.
[ rdpclient 876] [   89.914443]  Domain: "DOMAIN".
[ rdpclient 876] [   89.914484]  No shell.
[ rdpclient 876] [   89.914524]  No directory.
[ rdpclient 876] [   89.914564]  Window: 1856x1080@24.
[ rdpclient 876] [   89.914602]  PFlags 0x000000A8.
[ rdpclient 876] [   89.914642]  Keyboard 00000409:00000000.
[ rdpclient 876] [   89.914679]  My hostname "wt-129".
[ rdpclient 876] [   89.914719] TCP: connecting to 192.168.175.15:3389.
[ rdpclient 876] [   89.916407] TCP: connection with 192.168.175.15:3389 established.
[ rdpclient 876] [   89.916572] Turn keepalive on.
[ rdpclient 876] [   89.917368] Free ram after buffers allocation: 836252 KB.
[ rdpclient 876] [   89.927516] Process RDP server certificate.
[ rdpclient 876] [   89.927600] RDP5 encryption (X.509).
[ rdpclient 876] [   89.939080] Enable font smoothing.
[ rdpclient 876] [   90.039739] 32-bit color.
[ rdpclient 876] [  122.543074] errorInfo 0x00000000.
[ rdpclient 876] [  122.553098] Receive Disconnect Provider Ultimatum.
[            gm] [  122.553198] TSClient (sessionId 3, pid 876) gracefully end.
[        rdpsnd] [  122.556790] Link lost.
[          pfac] [  122.557004] Process pid 876 terminated, status 00000009.
[            gm] [  122.565210] Run '/sbin/resolver 0x1794300 dns [192.168.175.15]', log '', env '', pid ''.
[          pfac] [  122.565304] Run /sbin/resolver 0x1794300 dns [192.168.175.15].
[          pfac] [  122.565580] Ok, PID 889.
[          pfac] [  122.571406] Process pid 889 terminated, status 00000000.
[            gm] [  122.577430] 192.168.175.15 => 192.168.175.15.
[            gm] [  122.582735] Free ram before fork terminal client /sbin/rdpclient (session 4): 836200 Kb.
[            gm] [  122.582798] Run '/sbin/rdpclient 4', log '/tmp/rdpclient.out', env '', pid ''.
[          pfac] [  122.582841] Run /sbin/rdpclient 4.
[          pfac] [  122.583016] Ok, PID 890.
[ rdpclient 890] [  122.590389] RDP Terminal Client, WTware 5.8.88/RPi, pipe 4, pid 890.
[ rdpclient 890] [  122.590819] Use /lib/ui32.so.
[ rdpclient 890] [  122.591460] Redirect sound.
[ rdpclient 890] [  122.591770] Make RDP session with 192.168.175.15, port 3389.
[ rdpclient 890] [  122.591830]  No username.
[ rdpclient 890] [  122.591878]  No password.
[ rdpclient 890] [  122.591919]  No PIN.
[ rdpclient 890] [  122.591960]  Domain: "DOMAIN".
[ rdpclient 890] [  122.591998]  No shell.
[ rdpclient 890] [  122.592036]  No directory.
[ rdpclient 890] [  122.592073]  Window: 1856x1080@24.
[ rdpclient 890] [  122.592110]  PFlags 0x000000A8.
[ rdpclient 890] [  122.592147]  Keyboard 00000409:00000000.
[ rdpclient 890] [  122.592186]  My hostname "wt-129".
[ rdpclient 890] [  122.592226] TCP: connecting to 192.168.175.15:3389.
[ rdpclient 890] [  122.594017] TCP: connection with 192.168.175.15:3389 established.
[ rdpclient 890] [  122.594175] Turn keepalive on.
[ rdpclient 890] [  122.594908] Free ram after buffers allocation: 836200 KB.
[ rdpclient 890] [  122.607745] Process RDP server certificate.
[ rdpclient 890] [  122.607834] RDP5 encryption (X.509).
[ rdpclient 890] [  122.620484] Enable font smoothing.
[ rdpclient 890] [  122.707633] 32-bit color.
[           WPA] [  141.271355] eth0: CTRL-EVENT-DISCONNECTED bssid=70:db:48:68:f0:3d reason=3 locally_generated=1
[           WPA] [  141.271756] nl80211: Failed to open /proc/sys/net/ipv6/conf/eth0/drop_unicast_in_l2_multicast: No such file or directory
[           WPA] [  141.271799] nl80211: Failed to set IPv6 unicast in multicast filter
[           WPA] [  141.297948] eth0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
[           WPA] [  141.301119] eth0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=DE
[           WPA] [  141.418635] eth0: Trying to associate with SSID 'fornet5'
[           WPA] [  144.086883] eth0: Associated with 70:db:48:68:f0:3d
[           WPA] [  144.087043] eth0: CTRL-EVENT-CONNECTED - Connection to 70:db:48:68:f0:3d completed [id=0 id_str=]
[           WPA] [  144.087673] eth0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[           WPA] [  144.088272] eth0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=RU
aka
Разработчик
Разработчик
Сообщения: 10548
Зарегистрирован: Ср окт 01, 2003 12:06 am
Откуда: Роcсия, Тольятти
Контактная информация:

Re: raspberry 3b+ и cisco wlc/ap, потеря wifi

Сообщение aka »

sysardex писал(а):
Вт фев 18, 2020 11:47 pm
Можно как то заигнорить со стороны втвари требование точки соскочить на RU? Я подозреваю что производители малины или встроенной вифи карточки забыли пролицензироваться в RU
Нет такого требования "со стороны втвари". Втвари нет дела до настроек WiFi, втварь отдала пользовательский wpa_supplicant.conf в wpa_supplicant и ждёт, когда появится работающий интерфейс. Если проблема воспроизвелась на распбиане, значит проблема общелинуксовая и гуглить можно про линуксы в целом. В wpa_supplicant.conf ещё много интересных прараметров.
Ответить